Below is definitely the whole procedure for how can our machines work ad the detailed steps ,this really is to have an iphone repair .only for your reference .Our machines are fit for smasung galaxy ,blackberyy ,HTC ,LG etc ,all the touch screens on the market under 7 inch is going to be okay .
Step One :Semi-automatic lcd separator : place the broken part around the machine and set up-up temprature to 80?---90?,after temprature is okay , fasten the broken part and begin to separate the front side panle glass from touch-screen and LCD ,remove the broken part
Step Two:Stick Removing Machine : connect electricity ,set-in the temprature to 200 ?,place the separated touch-screen around the machine ,make alignment ,and after that press along the upper handle , the blade will begin to wipe the glue around the touch-screen .Please observe that , the cable around the touch-screen are unable to be touched from the blade ,otheriwise it will likely be damaged .Which machine is pre-set well by Axis ,so you may not need to be concerned about this when the touch-screen is going to be destroyed by excessive strength .
Step3 :Manual laminator for OCA Polarizer : Following the above step , the glue is cleaned clearly besides there will probably remain a bit round the cable ,since you failed to touch this devote last step .But it's okay ,simply use a little knife to get rid of the remain glue .Then obtain a new front panel glass along with a new OCA ,first place the OCA around the upper area of the machine ,make alignment , ensure that the left side of OCA edge is around the middle area of the roller around the machine ,as well as the front side of OCA egde matches using the machine inner line .Place the front panel glass on the best place from the bottom panel from the machine ,and after that put along the upper part .This machine has 2 more Millimeter measurements ,the first is so that you can adjust the front side panel glass from left to right and something is so that you can adjust the front side panel glass from returning to front .So once you put along the upper part , you will notice how exactly does the OCA matches using the front panel glass ,when they can not match perfectly ,adjust the area from the front panel glass using the measurements .The vacuum pump will help you suck the front side panel glass within the exact place , so you will see no any sways ,finally take out the front side panel glass quickly towards the Parallel right side using the longer screw within the device ,simultaneously ,your left-hand will have to retain the upper part the roller flatly and so the OCA is going to be around the front panel glass Naturely .Ensure that there is absolutely no bubbles left onto it .For more information , please check our demo videos .Which step will have to practice for a number of times ,once you get the skills ,you are going to get it done quickly .
Step 4 :Make use of a mold to place the front side panel glass along with the touch-screen part making alignment manually .
Step 5 : Place the whole part within the OCA Vacuum laminator machine ,all the valves with this machine is pre-setup well for you personally ,just press those 2 start buttons simultaneously ,after just a few seconds , the vacuum chamber will Bounce automatically .Go out the part , you will find that the entire part is laminated flatly and tightly with less bubbles .
Step 6 ,Place the finished part within the autoclave bubble removing machine ,set-in the tempeture to 45? and time for you to 15 mintutes .The device will help you to put around 20pcs touch-screen parts at once .After 15 mintutes , you will definately get an ideal refurbished new part for the phone
Step 7 : Laminator for iphone bezel frame : Only iphone will need this task to laminate the bezel frame .Please kindly remember that our bezel frames are with glue re-pasting onto it , so you may not want to use any glue onto it , just place the bezel frame on screen and place them together within the customized mold ,make perfect alignment (3pcs molds will include the device , one for iphone 4 4s , one for iphone 5 5s ,and something for iphone 5c) .Not to mention , this machine will have to set-up tempature too , to 170 ? ,after reaching this degree , just place the mold around the tool and press the handle down for 3--5 seconds .And taking it , you will notice that the center area of the screen do not possess high tempature ,only the lower and upper area of the screen has , this means the device won't make any damage to touch screen from the phone .
Finally you will definately get an absolutely refurbished new phone .
For samsung , this is the same process , the only real difference is that you will want to separate the center frame first , just heat-up and after that make use of the alcohol liquid to create the glue not pasting anymore and split it .These process would be the same goes with iphone.As well as for samsung , you may not want to use the laminator for bezel frame.
For more information about LCD OCA, simply visit our website.
|